When your television is stuck on one channel and it’s driving you insane. Especially if you’ve attempted to fix it a few times but haven’t been successful.
Because of a problem with the remote, your Smart TV is locked on one channel. Some buttons may not operate since it is old and worn out. Alternatively, its batteries may be depleted. There may be a problem with the remote and the receiver. Another issue might be a lack of channel availability in your area.
Before you become even more upset, give up, or even worse…
Continue reading to learn why this occurred and what you should do about it, but if you don’t want to waste your time, here’s a video you can watch to save more time:
Why Is My TV stuck on One Channel?
A defective remote, a malfunctioning mainboard, an unresponsive digital box, or subscription troubles may all cause a TV to get stuck on one station.
- The remote has seen better days.
- The batteries in the remote control are dead.
- There is a conflict between the receiver and the remote.
- It’s possible that the channel you’re looking for isn’t available in your area.
- You don’t have Channel in your favorites list.
- The channel lock switch is turned on.
- The digital box is not working.
- The mainboard is broken.
1. The remote has seen better days.
When a channel refuses to change, the first thing to check is the functioning of the remote. Something is amiss with the TV even before you worry; pay attention to the remote. The majority of us do not properly care for our remote controls.
The remotes are not constructed of the strongest materials and are susceptible to wear and damage. When any button on the remote is touched, the remote will light up; however, if the button that is being pressed to change the channel does not light up, there is a problem.
Solution:
- To change the receiver’s channel, press the corresponding button. These are the buttons with arrows pointing to them.
- If you can’t change to your preferred station, it’s because your remote is broken or the batteries are dead.
2. The batteries in the remote control are dead.
Another typical issue with remotes is that they may consume the battery’s power much more quickly than one would expect.
Solution:
- Replace the batteries in the rear with a fresh set, and you should be good to go.
3. There is a conflict between the receiver and the remote.
Check to see if anything is blocking the TV’s remote and receiver. A new remote will not be able to change the channel if the digital box cannot pick up the signal.
Solution:
- Turn off the television.
- Remove the receiver from the TV and reconnect it.
- Turn on the television.
- Press the receiver’s button and try changing the channels using the receiver’s buttons.
4. It’s possible that the channel you’re looking for isn’t available in your area.
Most likely, the channel you’re attempting to change to isn’t available via your service provider. It’s also possible that the channel you’re looking for isn’t included in your current membership package.
Solution:
- Check if the channels network is available for your region, then
- You might need to upgrade your current plan to have more channels including the one you want.
5. You don’t have Channel in your favorites list.
There are many channel preference lists, and, likely, the channel number you’re pushing isn’t on one of them.
Solution:
- On the remote’s keypad, type in the channel number. If you notice that this switches the channel to the one you like, you’ll need to update your favorite list.
- Proceed by looking for the guidance button on your remote.
- You’ll discover which favorite list you’re on before switching to the all channels option. Make the necessary changes to your list.
6. The channel lock switch is turned on.
To be able to change the channel again, you’ll need to disable the channel lock.
Solution:
- If your TV has a password, enter it.
- The system manual will include all of the information you need about the channel list, as well as any special actions you’ll need to unlock channels on your TV.
7. The digital box is not working.
Digital boxes that are unresponsive as a consequence of internal damage might be the source of the problem.
Solution:
- Locate and disconnect the power wire to resolve your unresponsive digital box.
- Reconnect the power cable to the digital box after 30 seconds.
8. The mainboard is broken
If you’ve tried everything at home and still can’t get it repaired, it’s definitely time to phone the TV company and have a specialist sent out. If the television is completely broken, you have no control over it.
Solution:
- Take the TV to an engineer who specializes in your TV type.
Frequently Asked Questions related to TV stuck on one channel
Below are a few queries people ask concerning how they could fix their PC being stuck on the channel
1. My Samsung TV is stuck on one channel
Reverting to factory settings generally cures similar difficulties on models with the model number UE32M5520AKXXU and after that have been upgraded to the current software. Do this only after you’ve made sure the remote isn’t broken.
Take the following steps:
- Option to return home
- Open the options menu.
- Support may be found by clicking on it.
- Select a self-diagnosis option.
- Now go back to the beginning.
- To confirm, enter the pin.
2. My Vizio TV stuck on one channel
Because of a problem with the EEPROM memory or a malfunctioning mainboard, a Vizio TV might get stuck on one channel. If the TV’s mainboard is damaged, it will need to be replaced.
The workaround for this problem is the same for Vizio M3D470KDE or E371VL TV models. When the TV is stuck on one channel, the most typical option is to reset the system.
- Turn off the television.
- Remove the gadget from the outlet.
- For around 30 seconds, press and hold the power button.
- Re-plug the set after 10 minutes.
- Hold the power button down until the television comes back on.
- Check to see if the channel has changed.
3. My LG TV is stuck on one channel.
A defective mainboard, dead batteries, or signal interference may cause LG TVs to get stuck on one channel.
It makes no difference whether you have an older LG TV, such as the LG 37LG30, or anything newer.
To limit the options, go through the most apparent stages.
- Examine the batteries to see whether they are in good working order. There’s a good probability that your remote has become outdated, especially if you have an older television.
- Make sure the receiver and the remote sensor aren’t being obstructed.
Try auto-tuning if your TV isn’t too old. You’d have to push the smart button on the remote, which looks like a home, to do so. The auto-tuning option may be found in the options.
4. My Insignia TV is stuck on one channel.
Some Insignia TV models, such as the NS-50L260A13, may get stuck on a single channel. Switching to a new universal remote might solve Insignia TVs that are stuck on one channel. If the remote isn’t at blame, the problem is most likely with the TV’s mainboard.
If you have a newer model, here are some things to consider:
- Unplug any other gadgets that are connected to the television.
- Examine the remote’s battery.
- Both the receiver and the sensor should be cleaned.
- Restart the computer.
- Revert to factory defaults.
5. Xfinity remote stuck on one channel.
If you have an Xfinity remote, first make sure the buttons are working and that the batteries are in good condition.
Before making any alterations to the television, ensure sure the universal remote is working correctly. If you have a voice remote, such as the model XR11, follow the instructions below to reset it.
- For 3 seconds, press and hold the triangle button and the diamond D button at the same time.
- The light will change from red to green.
- Press 9 8 1 together
- The blue LED light on the remote will flash three times, indicating that it has been reset.
6. My DirecTV remote is stuck on one channel.
If your DirectTV remote is stuck on a single channel, you must first determine if you have the Universal or Genie remote. Depending on the remote, the proper procedures to resolve the issue must be done.
Checking the battery that you have placed in the remote is a basic remedy for both types of remotes.
It’s fairly typical to discover that the remote’s malfunction is due to a problem with the battery.
The steps to resolving this problem are as follows:
- Check for a solid green light by pressing any button on your remote. This indicates that your batteries are in good condition.
- If the light begins flashing rapidly, the battery is nearing the end of its life cycle and will need to be replaced shortly.
- If you notice no light or a sluggish blinking light, it signifies the battery in your remote is dead or fading. 2 AA batteries should be removed and replaced. Check to see if your channel has changed.
7. How can I use my remote to solve my TV being stuck on one channel
Try these steps for these different remote types:
Universal Remote Control
- Ascertain that your reset has been received and that the remote has been correctly linked.
- The brightness of the television must sometimes be reduced.
- Using a lint-free cloth, clean the remote as well as the receiver’s sensor.
- To reset the receiver, press the red button or disconnect it, then wait 15 seconds.
Genie Remote Controls
- To reset the DirecTV receiver, press the red button on the device.
- Using the pair/program remote option in the settings menu, reset the remote control.
- Resetting the remote to its default settings might also assist if nothing else works. Press the mute and select buttons at the same time. The remote light then flashes three times. Then, while pressing 9 8 1 and the choose button at the same time, make the remote flash four times to finish the procedure.
Read Also: How to Watch DIRTVision on Roku in 2022
In Conclusion
My Samsung 32″ had the same issue. The wire from the rear was also removed. It seemed to be stuck on one station in particular (which I don’t watch), so I went into the channel menu and DELETED that channel. When I press the button on the remote, it now skips over that channel.
I believe the issue is caused by the TV’s CPU failing due to a large number of channel input requests being buffered.
But, whatever the case may be, I hope this post will be able to assist you to solve your problem; please leave a comment if you find it useful; it may help someone else and urge us all to do better.
